saw filter act f 8065 892 mhz features ? low - loss rf filter for mobile systems ? low amp litude ripple ? no matching network required for operation at 50 ? ceramic p ackage for s urface m ounted t echnology ( smt ) ? lead- free production and rohs complian t package dimension s ceramic package: dcc6c pin configuration 2 input 5 output 1, 3, 4, 6 ground marking top view, laser marking " act ?: manufacturer?s mark ? f ?: saw filter ? 8065 ?: part number maximum ratings rating value unit input power level p 10 dbm dc v oltage v dc 12 v operating t emperature r ange t a 25 c storage t emperature r ange t stg - 40 ~ +85 c
saw filter act f 8065 892 mhz electrical characteristi cs item minimum typical maximum unit center frequency f c 892 mhz insertion loss il 885.00 ?. 909 .00 mhz -- 2.0 2.5 db absolute attenuation dc ?. 8 50.0 0 mhz 18 22 db 919.00 ?. 9 29.0 0 mhz 20 22 db 9 29.00 ?. 9 6 0.00 mhz 20 26 db 960.00 ? . 2000.0 mhz 20 26 db amplitude ripple (p - p) 885.00 ? . 909.00 mhz ? 1.0 1.5 db input / output impedance (nominal) 50 rohs c ompli ant electrostatic sensitive device typical frequency response
saw filter act f 8065 892 mhz stability c haracteristics test item condition of test 1 mechanical shock (a) drops: 3 times on concrete floor (b) height: 1.0 m 2 vibration resistance (a) frequency of vibration: 10 ~ 55h z (b) amplitude: 1.5 mm (c) directions: x,y and z (d) duration: 2 hours 3 moisture resistance (a) condition: 40c, 90~95% r.h. (b) duration: 96 hours (c) wait 4 hours before measurement 4 climatic sequence (a) + 70c for 16 hours (b) +55 c for 24 hours, 90~95% r.h. (c) -25c for 2 hours (d) +40 c for 24 hours, 90~95% r.h. (e) wait 4 hours before measurement 5 high t emperature e xposure (a) temperature: 70c (b) duration: 250 hours (c) wait 4 hours before measurement 6 thermal impact (a) +70c for 30 minutes ? - 25c for 30 minutes repeated 3 times (b) wait 4 hours before measurement requirements : the saw filer shall remain w ithin the electrical specifications after tests. remarks ? saw devic es should not be used in any type of fluid such as water, oil, organic solvent, etc. ? be certain not to apply voltage exceeding the rated voltage of components. ? do not operate outside the recommended operating temperature range of components. ? sudden change of temperature shall be avoided, deterioration of the characteristics can occur. ? be careful of soldering temperature and duration of components when soldering. ? do not place soldering iron on the body of components. ? be careful not to subject the terminals o r leads of components to excessive force. ? saw devices are electrostatic sensitive . p lease avoid static voltage during operation and storage. ? u ltrasonic cleaning shall be avoided . ultrasonic vibration may cause destruction of components. test circuit recommended land pattern
saw filter act f 8065 892 mhz packing information carrier tape reel dimensions outer packing type quantity dimension description weight carton box 0.85 carton box 2 0000 190190190 1. 8 0 unit: mm unit: kg
saw filter act f 8065 892 mhz recommended soldering profile a c e a act . all rights reserved. note: 1. the specifications of this device are subject to change or obsolescence without notice. 2. typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibilit y of the equipment manufacturer. 3. our liability is only assumed for the surface acoustic wave (saw) component(s) per se, not for applications, processes and circuits implemented within components or assemblies.
|
